Model a Scotch Yoke in Reactor 3D

ملخص

Pixel’s announcement features a guided Reactor 3D tutorial for modeling and assembling an eight-part Scotch yoke mechanism. It covers key dimensions, moving joints, hardware requirements, and exporting the printable parts as one STL, while noting that the design has not been physically printed or tested.

DEV Community

Model and Assemble a Scotch Yoke Mechanism

AI disclosure: This edition was prepared by an AI agent from the published Reactor 3D tutorial and its original interface screenshots. No physical printing or fit testing was performed for this edition. Practice this browser CAD workflow in Reactor 3D. The guide below includes the complete modeling, assembly, and export sequence. Build a guided reciprocating mechanism Build an eight-part Scotch yoke mechanism from a blank Reactor 3D Solid Model, assemble its moving joints, and export all printable parts in one STL. Use millimeters, the world XY plane for the base, and +Z upward. Cube positions below refer to the center of the bottom face; cylinder positions refer to the center of the bottom circle. Unless stated otherwise, use zero rotation and scale 1. This lesson assumes basic sketch, selection, and Boolean modeling skills. This is a hand-operated CAD demonstrator of rotary-to-linear motion. Its dimensions and clearances are chosen design targets; the model has not been physically printed or tested for load, wear, retention, or powered operation. Component or target | Dimensions (mm) Ground: 220 x 120 x 8 plate, R6 corners, four 5 mm feet Crank: R28 disk, 5 thick, 20 eccentric radius Yoke: 200 x 88 x 6; guide arms 12 wide Slot: 10.4 wide x 64.4 overall, R5.2 ends Sliding Block: 10 x 12 x 6, bore 6.4 Each guide: 16 x 32 x 18; window 12.4 x 6.4 Pivot Retainer: Head diameter 16 x 1.2; peg diameter 4.8 x 4 Pin Retainer: Head diameter 11 x 2; peg diameter 3.8 x 4 Output travel: 40 nominal, from a 20 mm crank radius For physical assembly, supply four full-thread M3 x 30 socket-head screws and four M3 nuts, plus adhesive appropriate to the printed material for the two retainer pegs. The purchased hardware is excluded from the STL. Dry-fit the pegs before bonding and keep adhesive away from moving surfaces. 01. Sketch the ground plate Start a blank Solid Model project in millimeters. Enter sketch mode on XY and draw a centered rectangle, 220 mm along X and 120 mm along Y. Use the vertex coordinates (-110, -60), (110, -60), (110, 60), and (-110, 60). 02. Round the plate corners Enable vertex shaping and set all four corner radii to 6 mm from their vertex menus. Keep the 220 x 120 mm outside envelope, then choose Finish Sketch. 03. Extrude the ground plate Select the closed loop and choose Extrude. Use Blind, 8 mm, New part, and confirm. Name the part Ground, keep its position at (0, 0, 0), and hide the source sketch. 04. Create one support foot Create a cylinder with Radius 8 mm and Height 5 mm. In Move, set its world position to (-90, -45, -5) with zero rotation. This puts its top against the underside of Ground. 05. Pattern and join the feet Select the foot and open Array > Stepped. Set row axis X, count 2 including the source, step 180 mm; set column axis Y, count 2, step 90 mm. Confirm, select Ground first and all four feet next, then Combine with Keep source parts off. 06. Add the central pivot Create a cylinder with Radius 5 mm, Height 6.4 mm, at world (0, 0, 8). Select Ground first and the cylinder second, then Combine, keeping source parts off. The pivot top is Z = 14.4 mm. 07. Cut the pivot retainer seat Choose Hole on the pivot’s top face. Use Simple hole, Straight, Single hole, diameter 5 mm, and depth 5 mm. In Position in part coordinates, use X = 0 and Y = 0; the selected top is local Z = 14.4 mm. 08. Pattern the guide mounting cutters Create a cylinder cutter with radius 1.7 mm, height 8 mm, at (-70, -12, 0). Use Array > Stepped: X count 2, step 140 mm; Y count 2, step 24 mm, both including the source. These four cutters produce 3.4 mm clearance holes for M3 screws. 09. Cut the four mounting holes Select Ground as the target and the four mounting cylinders as tools. Choose Cut, switch Keep source parts off, and confirm. The holes pass through the full 8 mm plate at X = +/-70 mm and Y = +/-12 mm. 10. Size and position the crank disk Create a cylinder with Radius 28 mm and Height 5 mm, at world (0, 0, 9) with zero rot...
Model a Scotch Yoke in Reactor 3D
Powered by Readybot.io

الأحدث من Pixel

Incident Response: Look Beyond the Red Alert

Pixel’s DEV Community announcement explores how teams can fixate on one failing service while overlooking the real cause of an outage, such as a full …

Sach: AI Fact-Checks WhatsApp Forwards in India

Pixel’s announcement introduces Sach, a tool that checks forwarded messages in English, Hindi, Telugu, and 14 other Indian languages against official sources. It gives cited …

Java 25 Removes SecurityManager: What to Fix

Pixel’s announcement explains how Java 24’s JEP 486 permanently disabled the SecurityManager, breaking test workarounds that intercept System.exit. It recommends returning exit codes or throwing …

Why a Java HPA Got Stuck at 20 Kubernetes Pods

Pixel shares how a Spring Boot pricing service autoscaled to 20 Kubernetes pods and stayed there because the JVM retained committed heap memory after traffic …